Advanced system functionsAdvanced system functions
Setting the delays
You can set a number of delay times via the menu DELAYS:
ENTRY DELAY The time you get to switch off the system after entering your house (factory setting 30 sec).
EXIT DELAY before the system is switched on when you leave the house (factory setting 60sec).
ANSWER DELAY before the system picks up the line when dialling in (factory setting 5 sec).
DIAL DELAY before the system calls out in case of an alarm (factory setting 30 sec)
Setting the delays:
1. To access the menu, press either the menu upp or down button . The display now shows ENTER PIN.
2. Enter you 4-digit PIN code (factory setting 0000). The display is cleard and shows a * for each number entered.
3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.
4. Use the menu buttons upp/downto go to menu item 8. DELAYS. Press OK to select this menu item. You can
also go to this menu item directly by pressing an 8 on the nuber pad.
5. Select ENTRY DELAY, EXIT DELAY, ANSWER DELAY OR DIAL DELAY and press OK.
6. Enter the time required (1-99 secunds). Press OK, press CLEAR to delete the values entered.
7. Press CLEAR again to quit the menu.
The entry delay only works for the Ds18 Door/Window Sensor if set to MAX and MS18 motion detectors in zon 15
and 16 other (other zones will respond instantly).
Clearing the memory of your security system.
You can delete sensors, remote controls, timers or all settings via the menu MEMORY CLEAR. The PIN code is
never erased. This code can only be reset by the factory.
1.To access the menu, press the menu upp or menu down button. The display now shows ENTER PIN.
2. Enter your 4-digit OPIN code (factory setting 0000).
3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.
4. Use the menu buttons upp and down to go to menu item 6. MEMORY CLEAR. Press OK to select this menu
item. You can also go to this menu item directly by pressing a 6 on the number pad.
5. Select CLEAR ALL SENSORS, CLEAR ALL REMOTES, CLEAR ALL TIMERS, CLEAR ALL THERMOSTATS,
CLEAR LOG OR MASTER RESET.
6. You are now asked to CONFIRM CLR. Press 1 for Yes or 2 for No.
7. Press CLEAR again to quit the menu.
CLEAR ALL SENSORS Remove a registered sensor
CLEAR ALL REMOTES Remove a registered remote control or Additional (wireless) sensor.
CLEAR ALL TIMERS Remove all timer settings at once.
CLEAR LOG Remove Event Log.
MASTER RESET Clear the memory.
Changing the access code (PIN)
The access code is your personal identification code. After changing this code, you are only one who has access
to the settings on the console. You also use this code to disarm the alarm via the number pad. Make sure you
memorise the code, because only the factory, or authorized representatives can help you reset the code to the
factory setting (0000).
1. To access the menu, press the menu upp or menu down button. The display now shows ENTER PIN.
2. Enter your 4-digit PIN code (factory setting 0000). For every digit entered a * will appear.
3. When the PIN code has been entered correctly, the word INSTALL will show up on the display.
4. Use the menu buttons upp or down to go to menu item 5. NEW PIN. Press OK to select this menu item. You
can also go to this menu item directly by pressing a 5 on the number pad.
5. Enter your new PIN code (4 digits). The new PIN can be seen on the display. Check if you entered the correct
PIN code and press OK.
6. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes,
you will quit the menu. If you choose No, you go back to the first menu item.
12
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales